 | 
|
EK-XRES 100 DDC 3.1 PWM MX (incl. pump) is a power efficient variant of EK-XRES 100 DDC 3.2 PWM (incl. pump) a High-Performance water cooling pump reservoir combo. It has been designed to lower the production costs yet still offer premium hydraulic performance at the best price.
The core of the unit is the market-proven EK-DDC 3.1 PWM water pump which uses only one 4-pin PWM FAN header for connection. This unit offers increased hydraulic performance (up to 15 %) compared to original factory top.
PWM control allows for automatic pump speed regulation depending on your CPU temperature. Full performance on demand or whisper quiet operation in idle mode!
EK-XRES DDC MX series reservoirs come preinstalled with anti-cyclone insert. Additionally, a PU anti-vortex foam is enclosed.
The main body features two G1/4 threaded ports of which one is an inlet (in the reservoir) and one is an outlet (from the pump). EK recommends the use of EK-ACF series compression fittings.
The tube is made of high-quality acrylic material, while the rest of the pump/reservoir body is made from injection molded quality ABS material.
EK-Cable Pump testing adapter is recommended to be used for testing purposes while leak-testing your loop and is intended to be connected directly to PSU, without the need for powering up the entire system.
This reservoir can be easily upgraded with longer tubes used by EK-RES X3 series reservoirs. Replacement tubes can be purchased separately via EK Webshop.
EK-XRES 100 DDC MX 3.1 PWM pump reservoir combo can also be upgraded with either:
The top of this combo unit can be used as an inlet by adding the EK-RES X3 - Multiport TOP and an EK-RES X3 - Internal Tube with the corresponding length to your reservoir size. The Internal Tube is important to prevent the splashing sound of the coolant inside the reservoir and to prevent coolant foaming. It is recommended that the end of the internal inlet tube is submerged in coolant.
Pump electrical and mechanical properties:
- Motor: Electronically commuted motor
- Rated voltage: 12V DC
- Power consumption: 6W
- Maximum pressure head: 2.6m
- Maximum flow: 500 L/h
- Maximum ambient temperature: 10-50°C
- Maximum fluid temperature: 10-60°C
- Materials: PPS-GF30, EPDM O-rings, Aluminium oxide, graphite
- Power connector: 4-Pin PWM FAN connector
- Cable length: 50cm
Technical data:
- Reservoir Diameter: 60mm
- Overall Height: 121mm incl. pump
- Mounting hole pattern: 50x50mm
Operational regime:
- PWM duty cycle: ~ 20-100%
- Default behavior: Runs at 100% duty cycle when no PWM feedback signal is present
Enclosed:
- pump/reservoir combo unit (incl. pump)
- mounting screws and plastic washers
- allen key 2mm
- allen key 2,5mm
- anti-vortex polyether black foam
- installation manual
Made in Slovenia - EU!
Pump made in Hungary - EU!
Alphacool's new Low Noise Edition of the Laing DDC for absolute silence!
The Laing DDC pump is one of the best known pumps in the watercooling industry. Recently we have been working with Laing to take the DDC to the next level. The new Laing DDC310 was designed with a perfect balance of power and silence in mind. Unlike other versions with the plastic base we have revised the design with new superbly tuned brass housing which aids the pumps cooling and guarantees longer life especially when placed in areas with limited airflow.
This new housing promises a longer life of the pump. Through the cooling fins and air flow as well as an internal thermal pad attached directly to the pump board maximum cooling is achieved.
Another feature is the included decoupling option. If a pump top with a M4 threaded mounting hole, such as the Alphacool Laing DDC Acetal top is present. The special M4 screws can be screwed directly into the decoupling set and then into the case.
The pump also comes as standard with an anti-vibration mounting system . Available in black nickel and silver nickel.
This pump should be the first choice for your watercooling system.
Technical Details
Scope of delivery
Note
Not suitable for continuous operation with liquids containing titanium dioxide or glycerine. Typically, many pastel colors use these additives.
Facebook
Instagram
RSS News
