 | 
|
EK-FC GeForce GTX FE is a high-performance full-cover water block for multiple NVIDIA® GeForce® GTX and Titan X (Pascal) based graphics cards. Please check our Cooling Configurator online compatibility system for detailed compatibility list!
This water block directly cools the GPU, RAM, and VRM (voltage regulation module) as water flows directly over these critical areas thus allowing the graphics card and it's VRM to remain stable under high overclocks. EK-FC GeFroce GTX FE water block features a central inlet split-flow cooling engine design for best possible cooling performance, which also works flawlessly with reversed water flow without adversely affecting the cooling performance. This kind of efficient cooling will allow your high-end graphics card to reach higher boost clocks, thus providing more performance during gaming or other GPU intense tasks. Moreover, such design offers great hydraulic performance allowing this product to be used in liquid cooling systems using weaker water pumps.
The base of the block is made of nickel plated electrolytic copper while the top is made of quality POM Acetal material. The sealing is ensured by quality rubber washers. Screw-in brass standoffs are pre-installed and allow for safe, painless installation procedure.
EKWB recommends the purchase of aesthetic retention backplate which improves the looks of your graphics cards and also provide some passive cooling to the circuit board VRM section. The EK-FC GeForce GTX FE water block is backward compatible with all EK-FC1080 GTX Backplates, EK-FC1080 GTX Ti Backplates, and EK-FC Titan X Pascal Backplates.
G1/4" threaded fittings can be used on both sides of the FC terminal. Up to four EK-FC GeForce GTX FE water blocks can be used on a single ATX form factor motherboard by using EK-FC Terminal (DUAL, TRIPLE or QUAD type) system or other means of interconnectivity. Please note that EK-FC Bridge & Link system is not compatible with this water block.
The block also features a special plastic cover over the block Terminal. This add-on is designed to reveal the graphics card model, visible from the side. The terminal cover is removable, it is fitted with 2 screws from the side.
The EK-FC GeForce GTX FE water block is compatible with all reference design GeForce GTX 1060, GeForce GTX 1070, GeForce GTX 1080, GeForce GTX 1080 Ti, GeForce Titan X Pascal and GeForce Titan Xp based graphics cards. The current compatibility list rounds up a total of 106 graphics cards that are on the market, but as always, we recommend that you refer to the EK Cooling Configurator for a precise compatibility match.
Enclosed:
- EK-FC GeForce GTX FE series water block
- Mounting mechanism with screw-in brass standoffs
- Necessary mounting screws, nuts, and washers
- 2x EK plug G1/4”
- 6mm Allen key
- Thermal pads
- Thermal grease EK-TIM Ectotherm (1g)
A premium aesthetic terminal cover for EK-Quantum Scalar terminals, EK-Quantum Scalar accessories like the Flow Indicator, and a replacement cover for stock GPU terminals as well.
The cover is machined out of a solid piece of aluminum which is then anodized to a silver shade to give it a premium look and feel. The cover can be attached quickly and easily by using the integrated pin screws located on the backside of the terminal cover.
The prime purpose of the product is to provide a terminal cover for users with EK-Quantum Vector RE RTX 3080/3090, EK-Quantum Vector Trinity RTX 3080/3090, EK-Quantum Vector Trinity RTX 3070, EK-Quantum Vector Strix RTX 3080/3090, and similar GPU water blocks which have a single piece terminal, which is then replaced with an EK-Quantum Scalar Flow Indicator. The EK-Quantum Vector Terminal Cover will provide an aesthetically cover for the screws, which blends in with the water block and flow indicator perfectly.
In the same way, the EK-Quantum Vector Terminal Cover can provide an aesthetical shroud for the screws for multi GPU setups using any of the EK-Scalar Dual or EK-Scalar Quad terminals.
Finally, any user who wishes to reduce the number of RGB LED sources in his PC, can use the EK-Quantum Vector Terminal Cover to replace the stock plastic cover on water blocks that have the two-piece terminal design (acetal terminal + plastic cover).
Technical Specification:
- Material: Aluminum
- Finish: Silver Anodization
Included:
- EK-Quantum Vector Terminal Cover
- Mounting screws
- 2mm Allen key
Compatibility:
- EK-Quantum Scalar Flow Indicator
- EK-Quantum Scalar Multi GPU terminals
- EK-Quantum Vector Water Blocks with two-piece terminal design
Facebook
Instagram
RSS News
